Description 1Mw 190 series gas gensets PLG-1100GF
Are you still wasting time looking for Gas Propane LPG Genset - Prime, Standby, Continuous power suppliers?
Do you still worry about product quality assurance?
Are you late in deciding to buy because of insufficient budget?
If you have these worries, stay and see.
NEW 1 megawatts 190 series HAITAI gas generator sets PLG-1100GF
Prime Power: kW kVA 1200/1500
Standby Power: kW kVA 1320 1650
Fuel: LNG, CNG, Natural Gas, Biogas.
All ratings data is based on operation under IS08528 standard.
Both 50Hz and 60Hz are available.
Available in the following voltage:
190 series gas generator set selected 190 series gas engine assembly high efficiency
Faraday generators,through DeepSea automatic controller to achieve stable power output.The
power performance,fuel economy and reliability of this gas engine reach world advanced level by
adopting world advanced mixing model,electronic control technology and lean-burn strategy. The
series of gas generating units can work both single or parallel operation according to the users requirement. lt has outstanding performance in the oil field drilling,natural gas power plants, biogas power generation,coal mine gas power generation
Feature of the 190 series gas generator sets
Long service life resulting from application-specific design
Lower operating and maintenance costs
Low emissions due to advantage technologies
Reliable in field-tested
Adapt to harsh conditions
1、Turbocharger pre-mixing technology, where gas and air are sucked in at the same time in the compressor, to be suitable for low-pressure gas,
2，The rarefied combustion technology uses WOODWARDs E6 control system to accurately control the air-fuel ratio. Reach the high - altitude combustion ratio, achieve rarefied combustion
3，The single point injection and air-fuel ratio closed-loop control technology can realize the closed-loop control of the air-fuel ratio (in). The engine can adjust the amount of air and natural gas according to the requirements of different working conditions and different speeds so that the engine can run in the best state.
4，Efficient and reliable design of the intake and exhaust system, the use of advanced high-pressure ratio, large flow supercharger, increase the flow area of the intake pipeline, improve the intake efficiency
5，High efficiency, low resistance and plate type oil cooler to improve cooling efficiency, increase the cooling area of air and lubricating oil.
6、The ignition system with high energy and high reliability is selected to make the combustion of each cylinder of the engine more stable and even.
Customers Benefits of 190 series
High reliable and outstanding performance due to field-tested technology
The engine design is based on continuous working of 24 hours per day, 7 days per week
High Power and maximum efficiency, the best ideal engine for applications of CHP, CCHP, Cogeneration
and distribution energy system
Low operating cost as a result of low levels of lubricant and fuel consumption, as well as extended service
intervals (component stability)
Low emissions due to state-of-the-art combustion technologies
Low space requirements due to compact design
Long service life resulting from application-specific-design and tailored machinery-configuration
Applicable for various types of gas like natural gas, APG (oilfield associated petroleum gas), shale gas, coal mine gas, biogas, landfill gas and sewage gas etc
Ensures the display continues to operate
in extreme cold weather conditions.
Provides true generator and mains (utility)
Provides clear accurate power
Provides secure and simple off site
monitoring. All ports are continuously active.
Provides multiple installation options.
Makes the module ideal for standard and
electronic engine applications.
Tracks the amount of fuel being used and
sounds an alarm if over/under fuel use is
Ensures the control module can be used
with the latest in modern electronic engine technology.
Ensures the load can be transferred
manually/automatically between mains (utility) and generator power.
Ensures the control module is suitable for worldwide use.
Customisable status screens.
Multiple date & time scheduler.
Charge alternator failure alarm.
CAN engine manual speed control.
Manual fuel pump control.
Engine exerciser.kW & kV Ar overload protection.
Reverse power (kW & kV Ar) protection. Unbalanced load protection.
Backed-up real time clock.
Configurable Gencomm pages.
SMS messaging start & stop functionality.
Modem diagnostic display screens.
Remote display support (max 3 units)
PowerKit Gas Engine DatasheetRatings Definitions - COP
Ratings Definitions - PRP
- Unlimited using time per year;
- Continuous power is the maximum power available at a constant load factor;
- No overload capability is allowed
Ratings Definitions - ESP
- Unlimited using time per year;
- The average load rate is no more than 70% over 24 hours;
- Overloading 10% for 1h within 12 hours of operation is allowed.
- he annual operating time shall not exceed 200h;
- The average load rate shall not exceed 70% over24h operation cycle;
- No overload capability is allowed;
- The acceleration of starting of engines are carried out in accordance with
Q/WCG136.13, and there's no engine process. From acceleration of starting to calibration speed shall be completed within 10s. Natural aspirated engine,
when the environment temperature is below 5°, need to increase preheat facilities to ensure that engine water temperature above 30°. When
environment temperature over 5°, no preheating facilities are required.
Supercharged engine, when the environment temperature is below 10°, need to increase preheat facilities to ensure that engine water temperature
above 30° When environment temperature over 10°, no preheating facilities are required
- No ability to overload;
- The annual operating time shall not exceed 500h while supplying a variable
- It has 10% overload capacity;
- Annual run time is unlimited;
- Working under variable or continuous load of less than 100%;
- The power load shall not exceed 70% of the calibration power when the device is running continuously.
- ISO 8528-1, ISO 3046, DIN6271+-5%
- All ratings are based on operating conditions under ISO 8528-1,ISO 3046, DIN6271. Performance tolerance of+-5%.
- Test conditions : 100 kPa, 25°C air inlet temperature, relative humidity of
30%. Derating may be required for conditions outside these; please contact the factory for details.
- Power output curves are based on the engine operating with gas system, water pump and lubricating oil pump, without battery charging alternator,
fan and optional equipment
The specification of the 1Mw 190 series gas gensets PLG-1100GF
Cylinders and Arrangement 20 cylinders V type
Cylinder Bore, mm GPL1200
Piston stroke ,mm 1200
Standby Power, kW kVA 1320 1650
RPM, r/min 1000
Total piston displacement,L 50/60
Heat consumption rate kJ/kW.h < 8850
Dspl L 71.4
Lub. oil consumption rate g/kW.h <0.6
Start method Gas
Alternator Faraday FD7B
Controller Smartgen/Deepsea HGM61100SE7320
Frequency Hz 50
Power factor 0.8
Dimension mm 5735 x 2030 x 27000
Weight kg 1800 (open type)
Prime Power (PRP):
Prime power is available for an unlimited number of annual hours in variable load application, in
accordance with GB/T2820 -97 (eqv ISO8528);
A 10% overload capability is available for a period of 1 hour within a 12-hour period
Standby Power Rating (ESP):
The standby power rating is applicable for supplying emergency power for the duration of a utility
power interruption. No overload, utility parallel or negotiated outage operation capability is available at this rating.
generally the rated power includes 380/220V, 400/230V, 415/240V, 440/254V, we make it according to client's
The DSE7310 is an Auto Start Control Module and the DSE7320 is an Auto
Mains (Utility) Failure Control Module suitable for a wide variety of single,
diesel or gas,gen-set applications
Attachment (Optional Parts)
20ft Container canopy
Scientific and efficient Special sand-proof waterproof blinds with illumination.
(Super Silent canopy)Containerized Canopy
CHP system (Exhaust Heat Collector)
1. The unique spiral winding structure increases the turbulence effect, and the heat exchange capacity per unit area is 3-7 times that of the traditional heat exchanger.
2. High heat transfer coefficient, high heat exchanger heat transfer efficiency, good heat transfer effect, high heat transfer coefficient up to 14000W/m·k, energy saving effect is remarkable.
3. Small size. With only one-tenth of the traditional tube and shell heat exchangers, it takes up less space and reduces infrastructure and installation and maintenance costs.
4. Using a small clearance design to increase the flow rate, the heat exchanger is not easy to foul, and the use and maintenance costs
5. Advanced design concept, the length of the heat exchange tube is 3-4 times the height of the cylinder, the material stays longer and the
heat transfer is more fully.
6. Spiral-wound elastic tube bundle design can effectively eliminate pipe vibration and stress due to thermal expansion and contraction deformation.
7. Unique 90 degree connection, heat exchangers all participate in heat exchange,
no dead ends and stagnant areas, reduce fluid resistance.
8. Counter-current heat transfer, asymmetric flow design, in the vapor-liquid heat transfer field has other advantages that can not be compared with heat exchangers.
Automatic Paralleling and Gridconnect Control System
This system can connect generator sets in parallel or connect the generator set to the grid automatically.
Oil and Water Heater
High Voltage Alternator 6.3kv and 10.5kv, High Voltage Electrical Control Cells (PT Cabinet
High Voltage outgoing cabinet
DC Panel, Groud Resistance Cabinet and low voltage distribution cabinet etc)
Both 50Hz and 60Hz are available.
Special voltages available.
Alternator brand Stamford,Leroy Somer, Marathon are optional.
Controller brand Deepsea,Comap are optional.
Special requirements for Soundproof Canopy, ATS, Parallel & Synchronization Control, CHP and Biogas Pre-treatment Machinery are optional
The data herein can vary depending on individual production
Sea-Level<1000m , Temp<40º